Author Topic: To low Pay out Bally Mustang (Read 12236 times)

JanGbg · « **on:** September 15, 2015, 07:39:08 AM »

Hello!
I bought this machine rather sheep. In the beginning not much at all worked properly. I have fixed all, but one thing is still not ok. It pays to little, for example:
2 pays 1-2 coins
4 pays 3 coin
10 pays 7-9 coins
20 pays 16-17 coins.
I have fixed with Bally in 20 years now and I now that you can adjust "Pivot roller switch" (1 on pic) at the hopper. I have done that and with same problem with payouts. I tried to cut Cables so only one switch of 3 is used on the switch unit.
Any suggestions what more I can do? I wonder if there is some power-peaks when coil counts up the payout? Maybe a solution is to mount capacitors (10nF) on the pivot roller switch and at the coil (2 on pic) who Count up unit?
(The "Count up unit" always stops in right position).

JanGbg · « **Reply #1 on:** September 15, 2015, 07:42:35 AM »

Here is a pic of my Bally Mustang:

buybestslots · « **Reply #2 on:** September 15, 2015, 08:23:05 AM »

easy fix wiper board is off a little un screw those screws and twist it a little real little

RiseLikeRa · « **Reply #3 on:** September 15, 2015, 08:26:02 AM »

Yes I would agree with better slots as the first action to take. A shot of the side of the hopper and the zero stop would help if this does not fix the issue.

Ra

JanGbg · « **Reply #4 on:** September 15, 2015, 09:03:35 AM »

Quote from: buybestslots on September 15, 2015, 08:23:05 AM

easy fix wiper board is off a little un screw those screws and twist it a little real little

Where are these screws placed you mean?

buybestslots · « **Reply #5 on:** September 15, 2015, 09:08:23 AM »

the board on side of hopper where wipers move on

JanGbg · « **Reply #6 on:** September 15, 2015, 09:16:27 AM »

Quote from: buybestslots on September 15, 2015, 09:08:23 AM

the board on side of hopper where wipers move on

Do you mean this 2?

RiseLikeRa · « **Reply #7 on:** September 15, 2015, 09:34:47 AM »

Yikes! I never seen that before. I am going to sit this one out lest I give some bad advice.

Ra

Amechanic · « **Reply #8 on:** September 15, 2015, 11:10:12 AM »

Those are the two screws.. Usually you can adjust the stop bumper for the adjustment, but I don't see what's being used for that on your hopper.. Usually the wipers should be in the 6 O'clock position when the are reset back to zero.. Can you show us a picture of what's being used for the stop?

buybestslots · « **Reply #9 on:** September 15, 2015, 11:32:03 AM »

yes those screws if the disc has move some it will short pay or over pay depending which way its off

JanGbg · « **Reply #10 on:** September 15, 2015, 12:11:45 PM »

Quote from: buybestslots on September 15, 2015, 11:32:03 AM

yes those screws if the disc has move some it will short pay or over pay depending which way its off

They are sitting realy hard! And as I said, the wiper allways "goes" to right position. Wipers also goes right if you pusch the plunger (in the step up coil) with a finger let say 10 times.

JanGbg · « **Reply #11 on:** September 15, 2015, 12:20:32 PM »

Quote from: Amechanic on September 15, 2015, 11:10:12 AM

Those are the two screws.. Usually you can adjust the stop bumper for the adjustment, but I don't see what's being used for that on your hopper.. Usually the wipers should be in the 6 O'clock position when the are reset back to zero.. Can you show us a picture of what's being used for the stop?

Yes!
Here is a pic when hopper is reseted:

JanGbg · « **Reply #12 on:** September 15, 2015, 12:22:10 PM »

And here a pic of the wipers after a 10 coins win. Machine only paid 7 coins.....

buybestslots · « **Reply #13 on:** September 15, 2015, 12:26:30 PM »

from your pic you can see disc is off top is in closer than lower end that will cause short pays

The Fatman · « **Reply #14 on:** September 15, 2015, 03:50:24 PM »

Also check the linkage and the 100 tooth disk on the back of the wiper board. Needs to operate smoothly and accurately. Clean off any old grease from the teeth and sides of the gear. Make sure the teeth are not worn down. Sometime the teeth get worn and the advance can be incorrect.
dave F

Jon · « **Reply #15 on:** September 15, 2015, 07:19:13 PM »

this is a picture of the zero stop on the back of the gear hundred tooth gear on the hopper

Jon · « **Reply #16 on:** September 15, 2015, 07:20:45 PM »

this is a picture of the metal tab and bolted to the lower switch bracket on the back of the hopper

RiseLikeRa · « **Reply #17 on:** September 15, 2015, 07:32:43 PM »

Jan:

Ok I am back in. The first picture of the hopper CLEARLY shows your payout board higher on the left than the right. The picture also shows that the finger on the 2 coin payout rests about mid contact as opposed to at the beginning of the trace or contact like it should. In small increments move the payout disc counterclockwise until you get the proper payouts. Also, clean the stu-gots off of that disc. It looks terrible.

Ra

JanGbg · « **Reply #18 on:** September 16, 2015, 12:21:06 AM »

Thanks a lot for all help and good advice! I will remove (and set it back rights) the disc later today and see if it helps.

You are great all of you! :-)

JanGbg · « **Reply #19 on:** September 16, 2015, 12:50:18 PM »

Nope! Still the same problem. Maybe my machine pay one more coin than before.

As I told Before I wonder if there is some problem with the Power, for exampel: Counters often only registrate 70-80% of in and out, and sometimes (when 2 coins win) I can hear the hopper start but shut off Before something pays out.

News:

NLG Site Navigation Menu

Author Topic: To low Pay out Bally Mustang (Read 12236 times)