91
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Wts wms bb2 ruby slippers cf game card $65 shipped
« Last post by topgun911 on Yesterday at 04:36:05 AM »Pretty sure os H13.11 and higher will work
Welcome to the NewLifeGames.com message forum!
|
91
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Wts wms bb2 ruby slippers cf game card $65 shipped« Last post by topgun911 on Yesterday at 04:36:05 AM »Pretty sure os H13.11 and higher will work
92
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: S2000 Non working boards« Last post by scottf11961 on Yesterday at 03:43:59 AM »Do you want them? For you, take them all..$60 +. I'm actually getting rid of all my S2000 machines and going a different route with the gameroom. Selling them all. Even my giant Ms Little green men
93
BALLY Game Maker / Re: Could use some assistance on my gamemaker V7200« Last post by SkyPilot on May 05, 2024, 11:26:13 PM »Yes, Chris, seems it's all pretty much "Do it until you figure it out" kinda thing with these machines..
I really appreciate your help!!!! Howard P.S. On the Residual Credit I put "No Gamble" and also, thanks to you, I just entered Coin Acceptor and not the one with COD Board 94
IGT AVP (Including G20,G23) / Re: IGT G20 Button compatibility« Last post by sixcardmark on May 05, 2024, 11:10:52 PM »I have swapped non-edge lit for edge lit buttons on a couple machines with no problems.
95
BALLY Game Maker / Re: Game Maker 7200, Hot Hot Hot setup issue« Last post by Chris-socal on May 05, 2024, 09:29:07 PM »Your settings look ok.
Is this error only one game or it won’t boot past this? You need to switch 7 and 8 96
JCM WBA 10, 11, 12, 13, 14, 20, 21, 22, and 23 Bill Validators / Re: WBA-13 V3.60 not allowing bills past sensor IGT S2000« Last post by lowlimitlootlane on May 05, 2024, 09:21:14 PM »OK, I will go on EBAY, I saw the EPROM software on there. If I install the eprom, and still have issues can I believe it is now isolated to an issue with the head unit? At that point would the head be servicable or trash? Thanks for your help!
97
IGT S and S-plus Reel Games / Re: Payout not matching pay table.« Last post by t28c34 on May 05, 2024, 09:20:49 PM »FIXED! Thanks to Sixcardmark, he sent me a SS6622 chip and solved two problems. I never realized that it did not have the right reel prom installed. Swapped it out and now the pay table matches the reels. Then went to into setup for the bill validator and was able to change and put in the right settings. With the wrong reel chip, setup would not let me change the setting. Machine is now properly working. Thank you NLG and guys that respond to helping out with issues.
98
JCM WBA 10, 11, 12, 13, 14, 20, 21, 22, and 23 Bill Validators / Re: WBA-13 V3.60 not allowing bills past sensor IGT S2000« Last post by RB on May 05, 2024, 09:03:43 PM »V3.60 is severely outdated. It should take ones anyway. You probably have a bad head but need to update the eprom to 3.80 or 3.83 if you want it to accept current bills.
99
IGT AVP (Including G20,G23) / Re: IGT G20 Button compatibility« Last post by RB on May 05, 2024, 08:54:54 PM »I see no indication that they wouldn't be compatible with each other.
Remember that the Dynamic Buttons are not Hot-Swappable. Always Power down when removing or replacing Dynamic Buttons. 100
JCM WBA 10, 11, 12, 13, 14, 20, 21, 22, and 23 Bill Validators / WBA-13 V3.60 not allowing bills past sensor IGT S2000« Last post by lowlimitlootlane on May 05, 2024, 08:32:25 PM »I recently picked up another project IGT S2000. I added a new MPU battery, did a RAM clear and rekey, and disabled the printer while trying to trouble shoot the BV.
I started with trying to run the BV in standalone test mode and it never accepted any bills. When I start up the machine the BV appears to boot normally, and bezel lights up. When putting in a bill it doesn't go to far. I have tried one dollar bills as well as new fives, tens, and hundreds. It doesn't even read the whole bill before rejecting it, and depending on which unit is used it can travel farther into the BV. The hundred travels the farthest, and the one travels the shortest before being rejected. Here is a video of what I am encountering. https://youtu.be/mH-52DCThpc Summary: I tried running in test mode, got a bill validator comm error. Restarted the machine and showed what i am experiencing trying to get a credit loaded through the BV. Any help on what to do next would be appreciated, I don't have any spare WBA transports or heads, trying to figure out what my next move should be. Thanks. |
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |