Author Topic: IGT S Plus Coral Reef not taking coins (Read 29917 times)

Amechanic · « **Reply #60 on:** October 03, 2018, 03:23:42 PM »

The only way to know if the wires are good would be to check each one with a voltage meter. I would meter each wire out to be safe.

sgolembiewski0903 · « **Reply #61 on:** October 03, 2018, 03:43:16 PM »

I know I sound dumb saying this, but I'm not veryproficient with a multimeter. How would I do this? Would I turn the machine on, and put the probe on the ends, and make sure that they give out a reading? Also, what is an acceptable reading so I know what I'm looking for?

sgolembiewski0903 · « **Reply #62 on:** October 03, 2018, 03:47:43 PM »

So I THINK I may have done it correctyl.. I put the positive on he ends and just grounded it on the coin chute... On the 12-pin connector some of the wires gave me readings, some did not. The orange/red tracer wire gave me a reading of about 9volts.

Amechanic · « **Reply #63 on:** October 03, 2018, 04:26:13 PM »

I myself would unplug that coin harness and remove it from the machine. You donâ€™t want to do this with power on. You can use any of these settings, (see pic), to check for your wirings Continuity. Do it without power. Put your meter on one of these settings and watch your meter as you touch your lead together. You should see it change from a 1 to a 0.. That means you have no resistance. This is also how you check resistors, coils, etc. So if possible pull that small wiring harness and check it from end to end. Locate the orange/red at both ends and connect your leads to those connectors.

sgolembiewski0903 · « **Reply #64 on:** October 03, 2018, 04:46:22 PM »

Just checked every all the wires on the harness, all passed and had continuity.

sgolembiewski0903 · « **Reply #65 on:** October 03, 2018, 05:02:15 PM »

Also, anyone know where I can find a clear socket for the chips? They are both 14-pin, right? Or do they consider that 28?

Amechanic · « **Reply #66 on:** October 03, 2018, 05:05:53 PM »

Total number of pins.

therockinelvis · « **Reply #67 on:** October 03, 2018, 05:09:39 PM »

Can you post a video to your picture site. Would like to see only the reels and displays. Start video, turn machine on, close door and take it until after the reels spin. Did you say the 21 went away? And now only the 3100 shows? You can leave the hopper out for this. Early on you said the hopper was not working. Did you find what was binding it? There is a hopper test also. I think #4 then turn the key and it should pay 10 coins

sgolembiewski0903 · « **Reply #68 on:** October 03, 2018, 05:43:40 PM »

You might not need the video, what it's doing when I turn on the machine is simply lighting up, the bill validator goes through it's noises, and then the display goes to code 21. No reel spin.

After I used the clear chip it would do the reel spin, work fine with test credits (the hopper worked fine also) but it would not take money, although the "insert coins" light was on. As soon as I messed with the CC/Optics it went back to code 21.

sgolembiewski0903 · « **Reply #69 on:** October 03, 2018, 05:46:42 PM »

Not sure if this link works, not exactly sur ehow to upload videos.. https://photos.app.goo.gl/ZJpRMbnxbjMwgzsDA

sixcardmark · « **Reply #70 on:** October 03, 2018, 05:52:03 PM »

Yes it works. You have a power issue, the 21 should be solid lit.

sgolembiewski0903 · « **Reply #71 on:** October 03, 2018, 05:54:14 PM »

It is solid lit, I forget who it was that mentioned this, but it has something to do with the way the display lights work that give it the illusion of going on and off in the video.

therockinelvis · « **Reply #72 on:** October 03, 2018, 05:57:42 PM »

Yes lcd flashes in video. With the door open, does the 21 stay lit? Or are they blank until you go into tests?

sgolembiewski0903 · « **Reply #73 on:** October 03, 2018, 05:59:29 PM »

The 21 stays lit w without the door open.

Edit: with and without

sixcardmark · « **Reply #74 on:** October 03, 2018, 06:08:10 PM »

EDIT: I just noticed that too, the 21 should not appear until after the BV cycles with door open.

therockinelvis · « **Reply #75 on:** October 03, 2018, 06:11:56 PM »

Clear it again

sgolembiewski0903 · « **Reply #76 on:** October 03, 2018, 06:13:46 PM »

The 21 comes on after the BV is done cycling, there may be like a .5 second overlap where both are on at the same time

sgolembiewski0903 · « **Reply #77 on:** October 03, 2018, 06:16:03 PM »

Quote from: therockinelvis on October 03, 2018, 06:11:56 PM

Clear it again

Clear the slot machine again with the clear chip?

sixcardmark · « **Reply #78 on:** October 03, 2018, 06:21:26 PM »

It looks to me like you are NOT getting the door closed and latched, it's still open. Make sure the latch is ALL the way down.

Right now my machine is giving the 21 and does same thing yours does in vid with the door open. When you latch the door the 21 will dissapear for a few seconds.

sgolembiewski0903 · « **Reply #79 on:** October 03, 2018, 06:34:59 PM »

Earlier when I tested the door optics it wotkwo fine. Is yhere a special way to close and latch these doors? I feel like iveI tried everything!

News:

NLG Site Navigation Menu

Author Topic: IGT S Plus Coral Reef not taking coins (Read 29917 times)