31
IGT I-Game and Game King / Re: IGT Game King Multigame doesn't boot up
« Last post by sixcardmark on Today at 08:00:35 AM »Yes, normal, try moving the wires to the other switch.
Welcome to the NewLifeGames.com message forum!
|
31
IGT I-Game and Game King / Re: IGT Game King Multigame doesn't boot up« Last post by sixcardmark on Today at 08:00:35 AM »Yes, normal, try moving the wires to the other switch.
32
IGT S2000 and Vision Games / Re: S2000 Buttons Not Recognizing Every Press and Lights Not Working« Last post by Stayouttadabunker on Today at 07:54:24 AM »Your bulbs...are they 12volts, or 6.3volt lamps?
33
Universal Reel/Video Games / Re: universal slot machine jam« Last post by bidault on Today at 07:07:24 AM »I am not an electronic specialist nevertheless the battery voltage is 3.8V and the diode D5 is bad. the diode D4 is good. To help me to check can you show me where is the 6116 ram and if there is specific points I must control. Can you tell me the specifictions for the diode D to buy a new one.
34
Universal Reel/Video Games / Re: Replacement NIMH BATTERY?« Last post by 61Wally on Today at 05:33:10 AM »OK I will try and find the schematic for this. I took the power supply out and when I opened it I didn’t see any noise filter. In that area it looks like something was in there once upon a time. Unless this is a totally different type of power supply? ( Couple pics of it ).
35
IGT I-Game and Game King / Re: IGT Game King Multigame doesn't boot up« Last post by kmarrocco on Today at 05:08:53 AM »I looked at the main door switches this morning. Only one is connected. Can you confirm if this is correct and the wiring is connected properly?
36
Bally Alpha Reel Games / Bally Alpha Elite error« Last post by sakwilla on Today at 04:54:20 AM »Hi all my Bally V32 Eite came up wih a NVRAM battery low error. i replaced it with a new one and cleared the machine. When I put the game and os card in after clearing It gets stuck on the screen below "Getting disk data"
I have cleared the machine many times and no issues until now. Any ideas or suggestions to fix this error? 37
Other Reel Games / Re: Hopper Agitator« Last post by slcjeeper on Today at 04:20:54 AM »Lance,
It’s not too common to find machines that accept different coin types. This is more common on European machines, but since mechanically the hopper can only process one physically sized coin, the other is sent directly to the drop. This is more commonly found on the play nickels or quarters for Ikes machines. Coins played go straight to the drop and the hopper only holds Ikes for payouts. Regarding the handle mechanism, if it can be pulled at anytime, including when the machine is not powered, I would suspect the handle mechanism may have had a pawl removed, or it may be stuck or missing a spring. Can you share a picture of the handle mechanism showing the front edge as well as the side facing the reel mechanism? Joe 38
SIGMA Reel Games / Sigma Sg 150 b plus machine help .I need some one to tell me what I'm missing« Last post by John jackson on Today at 03:00:55 AM »Please can some one tell me exactly what wires belong in the reset key and menu switch. The switch is gone and wires are just hanging and my machine has power but no lights are coming on but the treasure wheel on top is displayed my machines power supplys are good but i think I'm missing some cables as well please can some one help me figure out what I need to get my machine going please
39
Printers - ALL / Re: Need Help with Gen2 Netplex on IGT G20« Last post by sixcardmark on Yesterday at 10:42:04 PM »You can borrow one from a game king or s2000. (non-usb) That's what I'm using in my G23.
40
Printers - ALL / Re: Need Help with Gen2 Netplex on IGT G20« Last post by sftechgeek on Yesterday at 10:20:16 PM »After lots of frustration, I got the printer out and now I'm thinking my issue is probably firmware as no one seems to know the firmware version this printer is on. I didn't realize there is a bracket with a screw in the front that needs removing. However, you have to pop the button self down to access it.
Does anyone have a Gen2 they'd be interested in loaning me to test it out? Or can I send my printer to anyone who can upgrade the firmware? I don't have the energy to figure that part of it out myself. Gen2 Universal. As it is USB I'm assuming, GUU001A508 |
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |