IGT Barcrest Anything But Six Slot

[DP]

I have Door open M code, ( I have lined up the sensor nothing happened ) I have closure B code & a Printer door open code. ( I have a Epic 950 ithaca printer and the lights says it closed) Help
DP

[therockinelvis]

You have a S2000 not S+. Sounds like your MPU is bad. Check the green varta battery. They leak and kill the traces on the board. Also check the voltage of your main battery, should not be less than 2.9vdc

[DP]

Thank You I will check it out !!!!
DP

[DP]

What Reset key do I need for an IGT Barcrest s2000 Anything But Six, I’m trying to change the Denomination from $5 to $1 and change the Pay Out to the highest setting.
Thanks
DP

[therockinelvis]

You have an Enhanced board, RB has the correct part for you listed below. Sorry

[therockinelvis]

S2000 RAM CLEAR/KEY SETUP
1. Power off slot and remove MPU tray
2. Remove SB chip and replace it with CLEAR chip
3. Power on slot and wait for top two amber lights to lite up
4. Power off slot and remove CLEAR chip and reinsert SB chip
5. Leave door open and power on slot
6. Should read “TESTING MEMORY” then alarm sounds with message error “RAM ERROR”
7. Turn RESET key four(4) times and it should read “PRESS TEST SWITCH FOR 2-3 SECONDS”
8. Hold MPU white button and release
9. LED now reads “CLOSE MAIN DOOR” Close main door completely
10. LED now should read “TESTING MEMORY” and when finished you get “CALL ATTENDENT” Message
11. Open main door and alarm should sound
12. Turn reset key 3 times
13. LED should read “MACHINE TYPE MISMATCH”
14. Power off slot and remove MPU and SB chip
15. Insert KEY chip
16. Power on slot and wait for two amber lights to come on
17. Power off slot—remove KEY chip—insert SB chip
18. Power on slot with door open and LED should read “7 KEY CHIP CONFIG”
BASIC CONFIG SETUP
Button Usage:
1. SERVICE and CASH OUT buttons control up and down in menus (sometimes sideways too)
EXAMPLE: 7.1, 7.1, 7.3—will scroll through these
2. SPIN button cycles through options horizontally
EXAMPLE: 7.1---7.1.1---7.1.1.1
3. MAX BET button confirms and backs out of menu horizontally—like a backspace
Multi Denomination Setup—Must be done in this order
7.1.1.1 Accounting—Usually lowest used value—Set $.01
Use MAX BET to set and confirm—Cannot be reset without doing a CLEAR
7.1.1.2 Coin Denomination—Value of coin dropped—Set $.01
Use MAX BET to set and confirm—Cannot be reset without doing a CLEAR
7.1.1.3 Player Denomination—Value assigned to each player
Use SERVICE and CASH OUT buttons to set amount for each player
7.1.2 Game Selection—Assigns % pay to each player
7.1.1.4 Touch Panel—Assign player number to touch button (Not available for single denomination)
7.1.6 Machine Types—Upright
7.1.7 Token Payout—Use printer and not Hopper—DISABLE
7.2.2 Printer-ENABLE
Set the following if you are using a TITO
7.1.3.5 SYSTEM BONUS---LEGACY
7.1.5 SAS AFT Controller
7.2.1.1 SAS Validation Type—System Mode
7.2.1.2 Validation Security—ENABLED
7.2.1.4 HandPay Validation—Don’t validate handpay receipt
7.2.3.1 Voucher Redemption—SAS
7.2.3.2 Voucher Limit Follows Credit Limit
7.2.3.3 Change Voucher--ENABLED
7.2.4.1 Remote Handpay Reset Enabled
7.2.5 Coinless Mode—DISABLED
Close door and machine boots up—Open door and press white TEST BUTTON
3.1.4 Field Locked in coinless mode—set LIMITS
Hopper Limit---“0” Only if no hopper is installed and in coin mode
Credit Limit—10000
Jackpot Limit—10000
Bill Limit—3000
Set the following if you are using a TITO (Set in this order)
3.4.2.2 Bally Miser Channel—OFF (MUST BE DONE FIRST)
3.1.9 Serial Number (any number)
3.4.1.1.1 SAS Address—001
3.4.1.1.2 SAS Channel—3 (Bally Miser must to OFF to Set)
3.4.1.1.3 Primary Link Down—Game Enabled
3.4.1.1.4 Primary Hand Pay--Hand Pay Reporting Disabled
3.4.1.4 AFT Asset Number—1
3.4.1.3 Cashless-Primary * Progressive-Secondary * Legacy Bonus-Primary * ASDC-Secondary
Link Bonus –Secondary * Validation-Primary
If you plan to key chip again you must make sure machine has “0” credits on it

[DP]

Thank YOU !
So I use the correct Keys/Chip what are the #’s I need so I can buy them ?
Danny

[therockinelvis]

See post 4

[RB]

DP, your enhanced MPU uses a R board. The correct key chip is RBK00001. It performs clear & key functions. You can remove the Varta battery (recommended) but you must also remove the component at U16 or at least clip the 3 pins so it doesn't make contact. Therockinelvis is unintentionally steering you wrong. PM me if you need a key chip.

[therockinelvis]

Thanks RB, I have never had a R board. Are there special instruction for keying it? I changed post 4 so no one is misled

[RB]

It's similar to a Game King KEY 22, 28, 40. It give you options to Clear ram, E2 & apply key chip. It goes in the boot chip socket. After replacing the boot chip setup is just like a normal S2000.

Here's a good link about removing the Varta from a 1270:

http://newlifegames.com/nlg/index.php?topic=7931.0

[DP]

I need that key. The only IGT USB keys I have is a KEY 14-09 AVP DIAGNOSTIC and a UNIVERSAL EKEY R EKEY000007 2010 IGT
Please let me know and I will buy it from you.
Thanks
DP