Author Topic: Igt s plus 5 times pay (Read 10835 times)

Patrickmerc · « **Reply #60 on:** July 12, 2023, 06:36:42 PM »

Thanks Jim. I now have a display. I am not sure how to run the optic test you recommend

Stayouttadabunker · « **Reply #61 on:** July 12, 2023, 07:58:46 PM »

Good catch on the wrong plug placement Jim.
If you READ the flip cards, it'll pretty show you how to test the optics for the door open switch.

https://newlifegames.com/nlg/index.php?action=dlattach;topic=18866.0;attach=53770

What's showing on the display?

Click on photo below to enlarge if needed...>>>

Patrickmerc · « **Reply #62 on:** July 12, 2023, 08:27:17 PM »

Thanks for the response. I will let you know as soon as I can run the test

Patrickmerc · « **Reply #63 on:** July 13, 2023, 01:14:56 PM »

I got it back together but I get the reel tilt codes. I replaced reel #1. I bought the machine with a code 41. Now it says code 42. I hit the reset key and the first number that comes up is 50. I obviously don't know how to run the test properly as the next thing I get is all zeros.

Stayouttadabunker · « **Reply #64 on:** July 14, 2023, 07:32:46 AM »

The machine getting the reel codes could be a couple of things, either a bad MPU or mis-adjusted door optics...even a bad , loose ground wire on the optic harness somewhere along the lines could be triggering the reels to stop.
Also, check if any of the reel strips are loose on the baskets?
Make sure nothing rubs or touches the back top of the reel glass long display?
Did you tighten the display good? It's not leaning backwards onto the reel baskets?
The display should be up tight against the reel glass.

I believe "50" means Page 5 for "Player Selectable Credits"...I'm not sure....read the Diagnostic Flip Tests carrds.
Go here to this link below, and read it and try to understand it...>>>

https://newlifegames.com/nlg/index.php?action=dlattach;topic=18866.0;attach=53770

Anyways, keep hitting the little white Test button until you get to Page 10 on the display.
When you get to Page 10, turn the Jackpot Reset Key 3 times to get to diagnostic input test [13-0].
From there, close the door with the door latch in the fully downward position, while at the same time watching the [13-0] on the display.
The number zero or one should change to a number one or zero, or alternatively start flashing - meaning the door optics are working, and "seeing" each other.
If it DOESN'T change, then one of the optics is burned out or something else is wrong.

Patrickmerc · « **Reply #65 on:** July 14, 2023, 08:47:41 AM »

I will give it a try. Also I have yet to see the reels move by themselves when the door is closed or powered up. Thanks for your time and help

Patrickmerc · « **Reply #66 on:** July 14, 2023, 10:34:02 AM »

13.0 no changes

Stayouttadabunker · « **Reply #67 on:** July 15, 2023, 05:37:33 AM »

"No changes" in the zero means you hven't yet done any checks as mentioned in Reply #36.

The reels will not move unless you move them, or until the optics "see" each other.

Try this then, turn OFF the power switch, move the reels randomly to any position, turn the power switch back ON and tell us what happens.

Patrickmerc · « **Reply #68 on:** July 15, 2023, 09:27:04 AM »

Good morning. I tried it and the reels didn’t move.

Patrickmerc · « **Reply #69 on:** July 15, 2023, 09:37:59 AM »

I forgot to mention that I did check the reels. They all turn freely. I checked for voltage at the optic inside the machine and it appears to be correct.

jonbbrew · « **Reply #70 on:** July 15, 2023, 10:39:33 AM »

Quote from: Patrickmerc on July 14, 2023, 10:34:02 AM

13.0 no changes

So to clarify...When on the 13-0 and you close and latch door all the way, the "0" does not change to a "1" and doesnt go back and forth from 1 to 0? If that is the case then your optics are not working....Either bad, broken connection, misaligned or board issues. First go with the misalligned route and test again. Place a piece of tape where the center of the optics are on the case and the door as if it was fully latched. Then close and see if the tape lines up. If so, then you know they are aligned and now can move on to figuring out why they dont work. I would replace with a good set, align and test again...often thats the issue.

Patrickmerc · « **Reply #71 on:** July 15, 2023, 11:45:03 AM »

I would like to verify the location of the sensors. Does it matter where the transmitter and receiver go.

sixcardmark · « **Reply #72 on:** July 15, 2023, 12:13:24 PM »

Yes. The one with red and black wires mount to the door. The one with red and white wires mount to the cabinet.

Patrickmerc · « **Reply #73 on:** July 15, 2023, 01:53:22 PM »

They are installed correctly. Is there a way to test them? I got some advice to test them using my multimeter but I was told to check millivolts but I don't know how it works. If I test for power on the sensors I get system voltage when they are plugged in

jonbbrew · « **Reply #74 on:** July 15, 2023, 02:59:48 PM »

Quote from: Patrickmerc on July 15, 2023, 01:53:22 PM

They are installed correctly. Is there a way to test them? I got some advice to test them using my multimeter but I was told to check millivolts but I don't know how it works. If I test for power on the sensors I get system voltage when they are plugged in

Easiest way to test first is like i motioned and others probably too. Go to 13 test and see if it bounces between 0 and 1. Also make sure they are aligned as mentioned. Report back on that first.

Watch video https://youtu.be/MpZjM2dVPGs

Patrickmerc · « **Reply #75 on:** July 15, 2023, 03:19:40 PM »

13-0 no change. Alignment is good

Stayouttadabunker · « **Reply #76 on:** July 16, 2023, 06:03:44 AM »

Quote from: Patrickmerc on July 15, 2023, 09:37:59 AM

I forgot to mention that I did check the reels. They all turn freely....

They shouldn't just turn completely "freely"...ther should be noticable resistance.
Move the power supply connector Molex that plugs into the motherboard while watching the reels.
The reels should look like they're jolted with electricity as you move the Molex connector up and down the on the male pins.
If you take the Molex off, turn it around, you'll see that the housing becomes browned from overheating on one of the ground pins.

You can clean the female and male pins with De-Oxit or some sort of de-oxidization spray can you can get at an auto parts store.
Over time, the pins get de-oxidization...sort of like on car battery terminals and causes bad electrical contact.

Patrickmerc · « **Reply #77 on:** July 16, 2023, 09:49:10 AM »

Hi thanks for the response. I have replaced the power supply harness already. The reels are stiff when it's powered up I just don't see them move when I close the door.

Stayouttadabunker · « **Reply #78 on:** July 16, 2023, 05:24:17 PM »

Replacing that harness really does NOT fix the problem of oxidized male pins on the motherboard.
Some people just get lucky getting better electrical contact somewhat by rubbing off the oxidization when they pull/push on the Molex connector up and down on the male pins.

okay, could you try this with the door open?
Turn the power [OFF], move all three reels by hand about a 1/4 turn...like about 4 or 5 symbols.
Now turn [ON] the power switch....do the reels turn back to where they were before?

Patrickmerc · « **Reply #79 on:** July 16, 2023, 06:10:41 PM »

I replaced the board as well. I moved the reels and they stay put

News:

NLG Site Navigation Menu

Author Topic: Igt s plus 5 times pay (Read 10835 times)