Author Topic: S2000 triple lucky 7's issues (Read 17856 times)

qbert · « **Reply #60 on:** July 30, 2016, 08:43:06 PM »

Disconnect and press white button, navigate to 3.3.1 and see if the bv is enabled. Then reconnect. The bv may be bad.

Hogwild6161 · « **Reply #61 on:** July 30, 2016, 08:48:06 PM »

I have it turned on to enable, but what button would i push for "enter" on this machine? That may be the biggest newb question ive asked all day...

Amechanic · « **Reply #62 on:** July 30, 2016, 09:17:32 PM »

You use the deck buttons to enable and disable items. Usually a cash out, or bet one. Them Max Bet to confirm if I remember off the top of my head. I don't have my cheat sheet in front of me.

Hogwild6161 · « **Reply #63 on:** July 30, 2016, 09:21:44 PM »

Gotcha. I tried the bet max button, and didn't take me out of whatever I was trying to configure. It's actually saying everything is not configured, from bv, to printer, to dot matrix, the works. I'll be back at it in the morning...

Hogwild6161 · « **Reply #64 on:** July 31, 2016, 04:49:34 PM »

Same as yesterday, but have learned so much from yesterday. Would it be worth purchasing a different bill validator, and cash can, to see if that is the issue? Do the bill validators have lights on any kind in them, because I have yet to see any kind of light in mine.
Or, there is a guy here that fixes slot machines, but won't be able to look at it for 2 weeks. Any advice would be greatly appreciated.

qbert · « **Reply #65 on:** July 31, 2016, 04:52:35 PM »

What happened when you tried to enable the bv?

Hogwild6161 · « **Reply #66 on:** July 31, 2016, 04:57:29 PM »

I was able to enable it, then went into the auto config section, and the bv, along with everything else, under the enable netplex devices, say not responding.

qbert · « **Reply #67 on:** July 31, 2016, 05:03:38 PM »

Does the bv cycle when you turn the machine on?

Hogwild6161 · « **Reply #68 on:** July 31, 2016, 05:06:10 PM »

Yes sir, it does. For 3 to 4 seconds.

Hogwild6161 · « **Reply #69 on:** July 31, 2016, 05:44:15 PM »

Also, I think I have narrowed down the toggle switch to it being a workaround for the jackpot reset key. I did the reel test, and when it said to hit the reset key, it did nothing. I went ahead and toggled the toggle switch, and it went into test mode.

qbert · « **Reply #70 on:** July 31, 2016, 05:47:55 PM »

You probably have learned more about your machine than someone who your going to pay money to fix it.
I would purchase a working bv for IGT S2000 from one of the fine vendors listed on the home page and see what happens.
What else says it's not communicating with when you netplex configure?

qbert · « **Reply #71 on:** July 31, 2016, 05:53:00 PM »

Printer probably would need to be enabled with a key chip and without a TITO system the machine won't take printed tickets anyway. Dot matrix won't be there anything else?

qbert · « **Reply #72 on:** July 31, 2016, 05:54:11 PM »

You did say it has a cash can correct?

Hogwild6161 · « **Reply #73 on:** July 31, 2016, 05:59:20 PM »

Yes, it has a cash can. And the netplex config is, printer 2 not responding, Bill acceptor not responding, spectrum display not responding, Aux bonus device not responding, Aux dotm display not responding.

Hogwild6161 · « **Reply #74 on:** July 31, 2016, 06:05:43 PM »

Think this would work?
http://rudysdeals.com/index.php?route=product/product&product_id=3955

cowboygames · « **Reply #75 on:** July 31, 2016, 06:13:25 PM »

Have you traced all the wiring from the BV to the motherboard to make sure everything is plugged in? To that end, pull the transport out and make sure you have current, IGT software on it

Amechanic · « **Reply #76 on:** July 31, 2016, 06:20:40 PM »

Do you think that doing a clear and key to this machine might fix many if the problems?

Hogwild6161 · « **Reply #77 on:** July 31, 2016, 06:29:10 PM »

I traced the wire from the bv, and here's the pic I took. All the others you see end up going into a bigger black wire, and go behind the reels, all the way to the door. As the pic shows, there is one that is not attached to anything. Any idea on this one?

Hogwild6161 · « **Reply #78 on:** July 31, 2016, 06:30:31 PM »

Amechanic, what is a clear and key? Sorry to ask a very newbie question.

qbert · « **Reply #79 on:** July 31, 2016, 06:48:02 PM »

Almost sounds like this was set up as a progressive if it's trying to communicate with a spectrum, over head display etc.

News:

NLG Site Navigation Menu

Author Topic: S2000 triple lucky 7's issues (Read 17856 times)