41
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Aristocrat set chip
« Last post by KAD on Yesterday at 07:15:38 PM »bump
Welcome to the NewLifeGames.com message forum!
|
41
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Aristocrat set chip« Last post by KAD on Yesterday at 07:15:38 PM »bump
42
IGT S and S-plus Reel Games / Re: IGT Double diamond S Plus, RESTORATION« Last post by David Walz on Yesterday at 06:07:31 PM »Fast shipping on the ABLOY lock for the cabinet. Just rekeyed it, installed it.
I have the LED fluorescent working, and I think the lower light needs to be turned down a bit. 43
IGT PE and PE Plus Poker Games / Re: Tournament Mode?« Last post by LuckyDog on Yesterday at 05:46:29 PM »44
Bally Electromechanical / Re: Bally Slot Machine« Last post by mboessen on Yesterday at 04:53:08 PM »Hi, Wolftalk
I emailed some pictures to the address you posted. Let me know if you need more. I took a couple of pics of the hopper plug from each side in case that would be helpful. I removed the top glass. There is nothing behind it but a fluorescent light and reflector. There are no markings on the back of the glass. I'm posting that picture here as well. Definitely "Hat Symbols" on the top glass and reels. Game theme is "Yankee Doodle Dandy". Someone mentioned the wheels (Reels?) and maybe index wheels? Anyhow, also attached a couple pics of those from each side Again, I'm not inclined to go much farther unless I can procure a correct hopper assembly. Hopefully these pictures will help with that. Sure appreciate the help. Best Mike 45
Universal Reel/Video Games / Re: universal slot machine jam« Last post by Pitts256 on Yesterday at 04:19:38 PM »When there's an error code 12 you have to powerup the machine while holding the CPU Board "ALL CLEAR" button for about 2-3 seconds. The coin deflector chute solenoid (just below the comparator) should pull in indicating the CPU has loaded the system program and is running. The fact that ERROR 12 is returning means there's a problem with the CPU Board battery circuit for the HM6116L RAM chip. Could be the battery voltage is below 2.8 volts, the battery switching diode D5 is bad or there's no 5vdc to the RAM chip...switching diode D4 could be bad.
Error code 12 could also be telling us that there's a RAM ERROR. Could be a bad ground somewhere in the cabinet, the 5vdc is shorted to ground or there's a defective component on the main board. My ERROR CODE 12 experience has always been a bad battery or a defective "charging" circuit and in most cases clearing the error at startup didn't prevent the machine from running. At this point I'd do a thorough check on the circuit checking for an open trace or bad component and assuring that we have 5vdc to pin 24 of the 6116 RAM chip from the battery (power off) and VCC (+5vdc - power on). I'll keep looking for a logical reason why you can't get a run permissive. 46
Bally Alpha (Cinevision), and ALL Bally "V___" series - V5000, V2000, V1000, etc. / Re: Bally V5500 getting it working again.« Last post by David Walz on Yesterday at 03:25:24 PM »At least I found the lower glass! Kinda of difficult removing the Duct Tape that was on the inside without damage.
47
WMS Williams Video / Re: Button lights not working« Last post by Coloradonewbie on Yesterday at 03:03:36 PM »Already tried all that. I first put all new buttons and bulbs. Then I swapped the whole button Deck with the working one. Tried new harnesses also.
48
Bally Electromechanical / Re: Bally Slot Machine« Last post by mboessen on Yesterday at 01:02:52 PM »Hi, Wolftalk:
I see what the guy meant that mentioned you as someone I need to know. $250 doesn't seem all that bad for that thing if it works. I guess we need to figure out if it is the right thing for my machine. The web site won't let me post hi res pictures. I already posted one of the front of the machine open and closed in my first post. I'll re-read your post and attempt to collect the requested information. Might be able to get at it later this afternoon, but have some mowing to get done. Best, and thanks! Mike 49
Bally Alpha (Cinevision), and ALL Bally "V___" series - V5000, V2000, V1000, etc. / Re: Bally V5500 getting it working again.« Last post by David Walz on Yesterday at 12:38:45 PM »I have located a wiring harness, I will replace my bill validator wiring harness.
50
IGT S2000 and Vision Games / Re: S2000 after acting weird after using keychip« Last post by Newbooty on Yesterday at 11:31:45 AM »Where do you set repeat enabled? Another strange thing. If I put a 20 dollar bill in (25cent denom) , the machine will accept it ( 80 credits ) and immediately take 3 credits and spins the wheels once. This leaves me with 77 credits without touching any buttons. After that first spin on its own, operations go back to normal. bet 1, Spin Wheels and Max bet all work normally? Do you think a clear might fix the issue? Thanks again for your help |
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |