Author Topic: IGT Haywire, can it be fixed? (Read 29212 times)

jidrd55 · « **Reply #140 on:** October 27, 2018, 08:24:24 AM »

[quote author=jidrd55 link=topic=21673.msg116619#msg116619 date=1540144528
The SP chip I got with the boards was for 16mhz, I got the 10mhz, the seller is sending the correct chip, is this the reason nothing is working?

So I got the new sp chip 1207 and ss4072 installed them and nothing happens. I took the sp chip out and put the bv set chip in to see if the new mpu board, mother board, test button are working. Pressed the white button, numbers cycled through ending on 999 on the display panel along with other numbers maybe 2-0, can't remember; then I pressed the spin reel button and the numbers cycled through again ending on 999. So I set the 25 cent denom, pressed the white button shut the door and turned the rest key. Nothing showing on display board, coins drop out of the bottom and bv won't accept bills. Help!!!

sixcardmark · « **Reply #141 on:** October 27, 2018, 08:44:27 AM »

Did you use the clear chip instead of the set chip? Should not get 999 with set chip. Put sp and ss back in, make sure they are in right slot, right direction.

jidrd55 · « **Reply #142 on:** October 27, 2018, 10:26:51 AM »

ok the chips are back in and in the right direction. Still nothing.

Amechanic · « **Reply #143 on:** October 27, 2018, 10:37:36 AM »

You might want to look closely at your wiring connection plug to the mother board. If you had as much acid damage as you did, those connection in those plugs could be damaged. Just the vapors from the acid can damage those crimp connectors. I know a person who bought some S+ machines a few years back with similar damage from battery acid. He had to replace some of those cables.

jidrd55 · « **Reply #144 on:** October 27, 2018, 02:26:19 PM »

Sorry it's taken so long to reply, I'm a little under the weather; but It did run the numbers when I inadvertently put the clear chip in, just didn't get the 61 error code when the sp chip was installed. I put the BV set chip in, white test button, the spin reels button and digital display worked, also the .25 light is on and the reels can't be turned freely, do you think there could be something wrong with the game chip, or did it mess up the cpu board cause I put in a game chip for a 16mhz board?

Shaggy · « **Reply #145 on:** October 27, 2018, 03:21:56 PM »

When you close the door does the insert coin light up? If so, it may be just waiting for a coin to be inserted and the spin button to be hit.

Dave

jidrd55 · « **Reply #146 on:** October 27, 2018, 04:24:35 PM »

No it doesn't light up, coin drops straight through to coin tray. It is new comparitor, the green light doesn't light up, the BV doesn't accept money, also isn't the slot suppose to light up on the BV when it is working properly?

sixcardmark · « **Reply #147 on:** October 27, 2018, 04:36:41 PM »

CC only lites when door is closed. Did you change 9-0 to 9-1 when you did set chip? Need to do that to enable bv.

jidrd55 · « **Reply #148 on:** October 27, 2018, 04:45:25 PM »

Yes and set it to .25, closed door, dropped a quarter in it, nothing, tried numerous different bills, nothing.

jidrd55 · « **Reply #149 on:** October 27, 2018, 04:49:48 PM »

The so 1207 is supposed to a psr, I can't find any where on here , do I need that to be able to program the machine?

sixcardmark · « **Reply #150 on:** October 27, 2018, 04:52:32 PM »

Make sure the door lever is all the down when you shut the door. It looks like it may still be in open door state?

sixcardmark · « **Reply #151 on:** October 27, 2018, 04:55:14 PM »

Quote from: jidrd55 on October 27, 2018, 04:49:48 PM

The so 1207 is supposed to a psr, I can't find any where on here , do I need that to be able to program the machine?

You can't program the machine until you get a display! Right now it is blank.

jidrd55 · « **Reply #152 on:** October 27, 2018, 05:13:43 PM »

The door does not line up well, when it is open it drops a littl and is very hard to close, I tried checking the door sensors with some of the suggestions on different posts on here but was unable to determine if they were actually lining up, but isn't there supposed to be a code 61 even if the door is open?

sixcardmark · « **Reply #153 on:** October 27, 2018, 05:20:44 PM »

jidrd55 · « **Reply #154 on:** October 27, 2018, 05:22:21 PM »

Door is closed completely, bad game chip?

sixcardmark · « **Reply #155 on:** October 27, 2018, 05:25:28 PM »

61 or 65 and/or 67 whatever needs to come up and be cleared before using the set chip for bv.

jidrd55 · « **Reply #156 on:** October 27, 2018, 05:33:20 PM »

So I'm gonna order a different sp chip, do ss chips work with any sp chip or do you have to have a specific one?

sixcardmark · « **Reply #157 on:** October 27, 2018, 05:35:43 PM »

You need a 10mhz type 2 haywire SP.

Amechanic · « **Reply #158 on:** October 27, 2018, 06:34:13 PM »

I just changed my SP chip from a 1085 to a 1274 on my Haywire and I really like it.

jidrd55 · « **Reply #159 on:** October 28, 2018, 05:16:44 AM »

Amechanic, where did you get the new chip and what number is your ss chip? Would you consider selling your old chip so that I could try a known working chip? When chips are changed do you use a clear chip before installing the new chip? Last question, what set of clear and set chips do you need for the sp1274?

News:

NLG Site Navigation Menu

Author Topic: IGT Haywire, can it be fixed? (Read 29212 times)