Author Topic: S2000 5 REEL ENHANCED BOARD AFTER CLEAR & KEY I GETING A ERROR MESSAGE (Read 9744 times)

vegasbaby · « **on:** July 20, 2015, 04:12:08 PM »

HI

Just received this new IGT S2000 5 REEL -AS-IS-NOT TESTED

This is my first s2000 with enhanced board. I did a clear #224 then key 45 then after installing Sb chip & booting up I get the following error message,

AFTER ALARM,THEN TURN KEY GET

ASSERT FAIL CFG_BNS.C @ 500-DX601

no no key chip menu.

Is there something I'm missing ? Do my chips on board all look correct?

THANKS
MARK

cowboygames · « **Reply #1 on:** July 20, 2015, 04:28:52 PM »

Double check seating on all chips, make sure both batteries have proper voltage and make sure boards are inserted snuggly and try again. If green battery is low, leave machine on for a few hours, then cycle to see if it starts

vegasbaby · « **Reply #2 on:** July 20, 2015, 05:20:42 PM »

Green battery only has 1.1 volt,will that battery charge some by leaving machine on a few hours? Or battery is to far gone?
Round battery is in 5 volt range,if my meter is correct.

THANKS

buybestslots · « **Reply #3 on:** July 20, 2015, 06:14:55 PM »

gm 1 chip in your pic sure looks like its not in at top notch end

cowboygames · « **Reply #4 on:** July 20, 2015, 07:30:49 PM »

If the green battery is good it will charge while left on.

erbs · « **Reply #5 on:** July 20, 2015, 07:33:54 PM »

Also check for bent pins on the back of your mpu board.

erbs · « **Reply #6 on:** July 20, 2015, 07:37:06 PM »

I have had an error like that before. Cant remember for sure but I believe I ended up replacing the mpu. Hope that is not your case.

RB · « **Reply #7 on:** July 20, 2015, 08:11:57 PM »

SG000597s are not a match for your game. Try using 523s or 598s. Bet it will solve the problem. The WOF SIMM may or may not work.

vegasbaby · « **Reply #8 on:** July 20, 2015, 08:33:39 PM »

Well that is some good news,after the bad new of MPU maybe needing replacement. I will try those chips on Tuesday. Thanks for all the extra eye's on this problem.
I will up date Tuesday.

THANKS
MARK

vegasbaby · « **Reply #9 on:** July 21, 2015, 09:38:17 AM »

UP DATE

I installed the 523 game 1 & 2 chips & keyed. Now I get the netplex link is down. From my research on site,looks like it is caused by the green varda battery as it has 1.1 volts. Battery is on order.

THANKS
MARK

billdern · « **Reply #10 on:** July 21, 2015, 10:50:40 AM »

Mark,
try leaving it on for awhile now it may take a charge
Bill

vegasbaby · « **Reply #11 on:** July 21, 2015, 12:48:24 PM »

How long will it take to charge,or gather some needed juice?

billdern · « **Reply #12 on:** July 21, 2015, 01:24:20 PM »

I think mine took 40 minutes or so but I was able to turn it off and turn it back on and it started up

vegasbaby · « **Reply #13 on:** July 21, 2015, 03:11:11 PM »

HI

Well after 3 hours of leaving machine on to charge battery,i now get the following message blinking on display DISPLAY PASSES SELF TEST. Also cpu lites 3rd from top & last from top blink on and off. Rest of lites stay steady on. What is the above issues telling me?

MARK<iframe width="420" height="315" src="https://www.youtube.com/embed/8EaHt0AhYhw" frameborder="0" allowfullscreen></iframe>

vegasbaby · « **Reply #14 on:** July 21, 2015, 03:24:18 PM »

cowboygames · « **Reply #15 on:** July 21, 2015, 03:31:54 PM »

What does the voltage on the green battery measure at this point?

vegasbaby · « **Reply #16 on:** July 21, 2015, 03:59:48 PM »

2.14 VOLTS

kindgaming · « **Reply #17 on:** July 21, 2015, 04:05:57 PM »

Hi
you need to change the green batery , wartha 3.6v

cowboygames · « **Reply #18 on:** July 21, 2015, 04:15:36 PM »

It may be a bad battery, but I usually leave my machines on for 8 hours to make sure thoae batteries are fully charged. Kinda like the old cordless phones, if you ran it dead it generally took about that long to fully charge.
Don't be surprised if you still have a software related issue after getting that voltage either by charging or changing the battery. I've swapped SG's before and ended up doing a clear and key to get proper function to the game. Not always, but it's happened. The notable one was a Crystal Sevens, I hate that game, PITA

vegasbaby · « **Reply #19 on:** July 21, 2015, 07:37:55 PM »

Well at this point,will wait for new battery. Then see where im at.

Thanks for the help

MARK

News:

NLG Site Navigation Menu

Author Topic: S2000 5 REEL ENHANCED BOARD AFTER CLEAR & KEY I GETING A ERROR MESSAGE (Read 9744 times)