Author Topic: Coin out counter, E-130-10 (Read 12896 times)

DavidLee · « **Reply #20 on:** January 04, 2017, 01:17:26 PM »

Okay, got the counter fixed. Both originals had broken advancing armatures. Only needed to fix one as I found good one in salvage.
Made a new replacement part and shoulder bolt. The shoulder bolt was conceived from the end of a reel index arm. The original
was pressed, peened over and needed to be ground out for removal.

Bally Bill · « **Reply #21 on:** January 04, 2017, 09:30:57 PM »

Nice job David, your like the MacGyver of EM slots! The counters in one of my machine has ENM corporation label and it looks like they are still in business. I found counters that look just like mine on the website but they are only 24 volt version. I sent them a email with the part number to see if they still sell them OR maybe provide a solution for these old ones.

rdaniel · « **Reply #22 on:** January 05, 2017, 12:21:12 AM »

I called the company and asked that same question. Do they still make 48 volt counters, the answer was no more. Also I looked up the manufacturers catalog line and there are no 48 volt counters for sale.

DavidLee · « **Reply #23 on:** January 05, 2017, 09:08:45 AM »

If the counters you have don't work, open one up. If there is a coil and its bad, it most likely can be replaced.

Bally Bill · « **Reply #24 on:** January 05, 2017, 09:57:50 AM »

The counter on my .5 cent machine is not working but I see someone taped and put a wire nut on another wire and I'am not sure if I should connect all 3? .25 cent has a lower door counter and I was wondering if that one could be used on the .05 machine?

DavidLee · « **Reply #25 on:** January 05, 2017, 10:25:27 AM »

Billy,

Brown/white is the coins out and the white/blue is coins in.
Where does the white/blue wire lead to? Should be two counters in the reel mechanism.
The counter from the other machine should work fine. Probably test it on the other machine before installing.
Save the old counter as it may be repairable.

Bally Bill · « **Reply #26 on:** January 05, 2017, 07:57:00 PM »

Hi Dave,The .05 counter has a label that states "Direct to Cash Box" 2 wires coming out the back of the counter- orange wire is not cut and is attached to the reel mechanism, the white and blue is the other wire that is cut and taped together so maybe the cash box was used as the coin out counter?

DavidLee · « **Reply #27 on:** January 05, 2017, 08:38:32 PM »

Hello Bill,

White and blue I believe is the coin in wire. Also the cash box meter may be connected to the switch near the coin diverter depending on the machine. There is a separate chute to the cash box that has a trip wire switch near the end to count coins, depending on the machine if it came with one installed.
Most likely the wire was cut when the counter stopped working.

Bally Bill · « **Reply #28 on:** January 05, 2017, 09:17:31 PM »

Thanks for that information David, another reason why I need to find a donor machine for parts

DavidLee · « **Reply #29 on:** January 06, 2017, 06:43:46 AM »

Bill,

http://orangecounty.craigslist.org/clt/5944246930.html

Wow just saw this on CL Vista, Ca. Not for parts a real nice machine with stand, $300.

Sent you a text earlier, hope you get the info.

Dave

rdaniel · « **Reply #30 on:** January 06, 2017, 10:59:52 AM »

That might be an "E" machine with circuit boards, not an EM. Best to contact the owner and see what the tag says.

Rdaniel

DavidLee · « **Reply #31 on:** January 06, 2017, 11:14:34 AM »

Could be an E machine. Where would the logic board be located?
Will try to find out.

Jon · « **Reply #32 on:** January 06, 2017, 12:25:37 PM »

Looks to me like a 1090

DavidLee · « **Reply #33 on:** January 06, 2017, 12:59:54 PM »

Jon,

Exactly what I thought.
The earlier list said 1019, didn't think there was a 1019.
Listing has been updated without model number.
Sent email to guy asking for info on ID tag, if the is one.

Amechanic · « **Reply #34 on:** January 06, 2017, 01:49:13 PM »

That's an EM Slot machine.. I see a dash pot switch by the air cylinder and the payout counter is on the bottom right rear of the floor behind the over flow chute.

DavidLee · « **Reply #35 on:** January 10, 2017, 09:07:44 PM »

Put a couple of counters into a machine today.
Veeder-Root made for Bally..
Note if your coin out counter test good, but still doesn't work.
Check to see if the door switch lower right has be disconnected and or removed.
The brown / white brown / yellow wire runs from the payout step up unit through the switch then to the coin meter.
In some machines.

OldReno · « **Reply #36 on:** January 11, 2017, 12:02:38 PM »

Of course the door switch was to allow mechanic to check pays etc. & not screw up accounting...
Veeder root, great meters!!!

Bally Bill · « **Reply #37 on:** January 18, 2017, 08:15:24 PM »

Hi David, E-mailed the C/List seller(Gin) but never received a reply about that slot machine....

DavidLee · « **Reply #38 on:** January 18, 2017, 09:25:15 PM »

I also sent a message, but never heard back.
Maybe sold, but not removed.
Will check the post for any updates.
Made an offer on a 1090 in Fresno for parts.
It's a Summit machine, but still has some useable parts.
Haven't heard back from the guy.

Bally Bill · « **Reply #39 on:** January 19, 2017, 07:22:33 AM »

it seems like there are not a lot of Bally EM for sale lately and the cheap ones go fast, I noticed the other day that one of the payout counters is skipping or not registering the correct payout all the time. Works good for most of the payouts (2,4,10,14,18) but gets funky when it hits 3 bars/100 coin payout so do you think that arm is worn or loose?

News:

NLG Site Navigation Menu

Author Topic: Coin out counter, E-130-10 (Read 12896 times)