New Life Games LLC
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length

News:

Welcome to the NewLifeGames.com message forum! 

 


NLG Site Navigation Menu


Archives of old posts can be found at...... Newlifegames.net/nlg/

Author Topic: Bally 5000 +  (Read 1905 times)

0 Members and 1 Guest are viewing this topic.

Offline meatman1010

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 84
  • Reputation Power: 6
  • meatman1010 New User has no influence.
  • Gender: Male
  • NLG
Bally 5000 +
« on: April 25, 2017, 10:26:29 PM »
Hi, I picked up a 5000 +  the guy I bought it from said there was a 82 error  . Brought it home, checked batt. It was at 1 volt so changed it, checked all connections,  it took the quarters, pushed start , all 3 reels spun , 1st one stopped , then about 10 seconds later 2 and 3 stopped , then all 3 turned slow. A  41....reel 2 error  came up . I pulled out the upper board, turned it on , it cleared no problem.  All connections were checked. I also took reel out and checked connection inside the reel could I have bad sensers . Not sure what to do. Any ideas ..thank you...

Offline Badbaud

  • Topic Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Bally 5000 +
« Reply #1 on: April 25, 2017, 10:47:44 PM »
It could be your power supply is failing.
Check it's voltages in the machine to see.
The 24VDC would be the one powering the reels.
See the attached page.
Let them that don't want any, have memories of not getting any.

Offline meatman1010

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 84
  • Reputation Power: 6
  • meatman1010 New User has no influence.
  • Gender: Male
  • NLG
Re: Bally 5000 +
« Reply #2 on: April 25, 2017, 11:15:28 PM »
Thanks , I will check that tomorrow.  I did notice the board inside reel 2 was a little dark in a spot. Could it get that warm. Thanks...

Offline meatman1010

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 84
  • Reputation Power: 6
  • meatman1010 New User has no influence.
  • Gender: Male
  • NLG
Re: Bally 5000 +
« Reply #3 on: April 25, 2017, 11:59:34 PM »
What if I swap plugs on 2 + 3. ..If 2 stops like 1  may be it's at the conections 2 board ...

Offline Badbaud

  • Topic Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Bally 5000 +
« Reply #4 on: April 26, 2017, 07:06:22 AM »
Try that, also unplug and plug in the connectors on the reel driver board under the reels a couple of times.
Dirty pins could be the problem.
Let them that don't want any, have memories of not getting any.

Offline meatman1010

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 84
  • Reputation Power: 6
  • meatman1010 New User has no influence.
  • Gender: Male
  • NLG
Re: Bally 5000 +
« Reply #5 on: April 26, 2017, 11:24:51 PM »
Hi, well I unplugged  the pins going to the reel board  for reel  1 2 3  about 10 times and it is working now. They actually  work better only pushed in 3/4 of the way in. That's kinda strange?  do I need the key pad to change the sound setting?  I see in the manual there is different  sound options. Also the lights for the  collect credits, play max credits, and play one credit don't light up. Burnt out?  Do I need the key pad to change from credits to non credits. In the manual it says how to do it but also mentions the pad...thank you...

Offline Badbaud

  • Topic Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Bally 5000 +
« Reply #6 on: April 27, 2017, 06:43:54 AM »
I posted a sticky on how to make your own keypad but you could post a WTB to see if someone will sell you one.
Let them that don't want any, have memories of not getting any.

Offline meatman1010

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 84
  • Reputation Power: 6
  • meatman1010 New User has no influence.
  • Gender: Male
  • NLG
Re: Bally 5000 +
« Reply #7 on: April 27, 2017, 10:31:36 PM »
Hi thanks....I am  getting code 41 back so I put reel 2 wires in reel 3 plug and reel 3 wires in reel 2 plug and no error came up. Of course the pay didn't jive correctly cause they were switched around . Could d it possibly be one of the wires going from the reel board by the motor to the board under the reels. Should I check each wire end to end to see if there is a break in one of the lines. That's weird that no error came up when I switched 2 and 3 around. Is it because now 2 was the last one to stop and no error   could acurre? When I do a test, 1 and 3  seem to be normal but 2 seems to take longer. Thanks...

Offline Badbaud

  • Topic Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Bally 5000 +
« Reply #8 on: April 27, 2017, 11:11:12 PM »
If you have the IDC (insulation displacement connection, where the wire is wedged between two blades) type of connectors going to your reel driver board it may be a good idea to get a small flat blade screwdriver and shove every wire into it's connection.

If you have a Molex KK100 type of connector you can pop each pin out and clean it with a pink eraser then spread it apart and reinsert. Make sure the keeper tab is spread back out before inserting.
Let them that don't want any, have memories of not getting any.

Offline meatman1010

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 84
  • Reputation Power: 6
  • meatman1010 New User has no influence.
  • Gender: Male
  • NLG
Re: Bally 5000 +
« Reply #9 on: April 27, 2017, 11:23:16 PM »
Thanks, I will try that . That's funny how it will work fine for 30 min. Then a 41 pops up.

 

Cell Phone and Pad Mode

imode wap wap2

NLG Archives

Archives @ newlifegames.net Wayback Machine

Contact Us

NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442
If you find this site helpful, please consider becoming a Contributing NLG Member with a monthly subscription to help cover the cost of pizza, coffee, aspirin, hosting, and bandwidth.
Contributing Members: get unlimited personal messages, can save topics and replies as drafts,
can post to the Classified ads, get unlimited access to the downloads, and also get this minty badge:



**Subscription Link** (Click Here) **Subscription Link**



           
If you would rather remain anonymous Thank You or just want to help support the site, please use this "make a donation" button:




From your entire NLG staff, thank you for supporting NLG.


New Life Games LLC 1788 HIGHWAY 95 UNIT 30 BULLHEAD CITY AZ 86442




Newlifegames.com     Newlifegames.net     Newlifegames.org

Newlifegame.com     Newlifegame.net     Newlifegame.org    Newlifegames.us

   New Life Games     NewLifeGames  NLG

 We Bring new Life to old Games    1-888-NLG-SLOTS

Are all Copyright and Trademarks of New Life Games LLC 1992 - 2022


FAIR USE NOTICE:



This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml
If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.




The NewLifeGames.com website is optimized for use with Firefox and a minimum screen resolution of 1600 x 900 pixels.

SimplePortal 2.3.5 © 2008-2012, SimplePortal