IGT Spin Til You Win

[alfa75]

Can anyone tell me the type of this slot? Is it possible to set it so that it pays out immediately on a win without hitting the cash out? I'm planning to buy this machine, so unfortunately I can't test it out beforehand.

[Stayouttadabunker]

From your photo, even though it doesn't have a DBV, I would say that it's an older IGT S+ slot machine.
Ask the seller if they could submit you a picture of the MPU circuit board.
Or at least a photo with the door opened.

On that model, the MPU circuit board would be located vertically inside against the left wall of the cabinet.
To give oneself some room, they would first slide out the coin hopper, put it aside, grab the big black knob on the MPU tray, wiggle it upwards and out.
If there's a wiring harness plugged into the vertical circuit board, then it's a straight "S" or "M" model.

This machine was primarily designed as a coin-based machine.
The default payout setting was for the coin hopper to pay out wins into the coin tray.
If it's set to accumulate winning credits to the display, it's just a simple matter of hitting cash button once, to make the machine pay out the way you want it to.

[alfa75]

Many thanks for the helpful answers. This is a photo with the door open, is it possible to recognize the type?

[Stayouttadabunker]

That's an S+.
The upright left wall vertically-mounted 10 Mhz MPU circuit board tells me that.
You can see the blue potentiometer volume dial on top towards the front.

[alfa75]

I am looking for a replacement for the Coin Comparitor (see photo), who can help me find the right one?

[Stayouttadabunker]

I am looking for a replacement for the Coin Comparitor...

That is the correct coin comparitor for your S+ machine.
What do you think is wrong with it, besides it missing the sample coin?
Is the coin sensitivity dial adjusted correctly?
Take a small jewelry screwdriver, stick it in the adjustment screwhead and turn it fully counterclockwise, then turn it clockwise 1/4 turn.
That will put the sensitivity in the ballpark area for American quarters.

[jay]

Did you solve your issue of intermittent pay outs ?

[alfa75]

Did you solve your issue of intermittent pay outs ?

I didn’t have the slot with me, I won't be able to test it until January/February at the earliest. Do I need any clear cards or similar so that I can make the settings?

[alfa75]

I am looking for a replacement for the Coin Comparitor...

That is the correct coin comparitor for your S+ machine.
What do you think is wrong with it, besides it missing the sample coin?
Is the coin sensitivity dial adjusted correctly?
Take a small jewelry screwdriver, stick it in the adjustment screwhead and turn it fully counterclockwise, then turn it clockwise 1/4 turn.
That will put the sensitivity in the ballpark area for American quarters.

I didn't even notice that the coin was missing, I will be able to check it as soon as the slot is with me, this will be the case in January/February. I will let you know here if it worked. Thanks anyway for the important tip!

[jay]

You can change most settings without anything special.
The exception is the bill validator which needs a set chip.

People have had issues after a battery change where the cmos got corrupted and a clear chip is needed but this is a rare occurrence and not something that is routinely needed. It brings all settings back to factory. The. You need to spend a lot of time setting everything back to regular use.

[alfa75]

You can change most settings without anything special.
The exception is the bill validator which needs a set chip.

People have had issues after a battery change where the cmos got corrupted and a clear chip is needed but this is a rare occurrence and not something that is routinely needed. It brings all settings back to factory. The. You need to spend a lot of time setting everything back to regular use.

Thanks, is not my first slot that I have, just want to be prepared as the import from the USA also takes a relatively long time for me.