New Life Games LLC
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length

News:

Welcome to the NewLifeGames.com message forum! 

 


NLG Site Navigation Menu


Archives of old posts can be found at...... Newlifegames.net/nlg/

Author Topic: Need Fixing 3200 Error  (Read 9578 times)

0 Members and 1 Guest are viewing this topic.

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Need Fixing 3200 Error
« on: March 13, 2014, 09:58:10 PM »
3200 error I've verify the hopper motor is working correctly and the coins and the wiper\knife free and clear.  Optical Free and clear and working on the hopper and the door.  After I push the reset and close the door.  Turn the jackpot key I get 00.  If I open the door pushed reset it goes to 3200.  And a five in the coins play box.  Also tried turning the power off for 5 minutes and same thing.Every time when I run set15 chip.  it will run for five or six Spins.  then it is back to 3200 error.  . :thank_you:








Duplicate post removed. Not necessary to post same question twice.
« Last Edit: May 08, 2014, 06:25:37 AM by Ron (r273) »

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #1 on: March 18, 2014, 09:40:24 PM »
Scratch Head 3200 error I've verify the hopper motor is working correctly and the coins and the wiper\knife free and clear.  Optical Free and clear on the hopper and the door.  After I push the reset and close the door.  Turn the jackpot key I get 00.  If I open the door pushed reset it goes to 3200.  Also tried turning the power off for 5 minutes and same thing I also ran the set 15 chip and I still get the same thing.  S-plus chip 1048

Offline rslots

  • Contributing NLG Member
  • NLG Member 101 to 250 Posts
  • *
  • Posts: 144
  • Reputation Power: 16
  • rslots New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #2 on: March 23, 2014, 02:13:10 PM »
May be a stupid question but are any coins coming out of your hopper when this happens or can you hear the hopper running? Have you tried running a hopper test?  3200 means the coin out sensor has sensed a coin in it longer than 700msec so it thinks there is a coin stuck in the sensor.  Could be a bad sensor. 

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error read beteen the lines
« Reply #3 on: May 03, 2014, 06:31:12 AM »
May be a stupid question but are any coins coming out of your hopper when this happens{{{{NONE }}}or can you hear the hopper running?{{{ NOPE }}} Have you tried running a hopper test?{{ I CANT I THINK ITS IN TILL }}  3200 means the coin out sensor has sensed a coin in it longer than 700msec so it thinks there is a coin stuck in the sensor.{{ free & clear}}  Could be a bad sensor.{{ I just replace it }} {{{if I used the reset 015 or 057 it works until it hit a pay out then its back to 3200 

Offline Buzz

  • In Remembrance of our lost NLG Members
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 434
  • Reputation Power: 79
  • Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #4 on: May 03, 2014, 09:16:37 AM »
To clear a 3200, assuming your door optics are good is open and close the main door.

Why did you get a 3200 in the first place ?  Most times the hopper brake is bad and lets one extra coin be paid out. More often than not it's the spring on the brake that's off or broken.
PUT BRAIN IN GEAR BEFORE PUTTING MOUTH IN MOTION

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #5 on: May 03, 2014, 09:28:19 AM »
its been rebuild spring is new

Offline Buzz

  • In Remembrance of our lost NLG Members
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 434
  • Reputation Power: 79
  • Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #6 on: May 03, 2014, 11:13:41 AM »
You know sitting in my back yard is a caterpillar track loader ( no tires it runs on tracks like a bull dozer ) About 10/12 years ago the engine was rebuilt, I think parts alone were around 4 grand. You know that loader hasn't moved more than 10 feet since it was rebuilt.  Here lately I've been thinking the mechanic that did the job must have screwed up. ( next time I'll do a better job )
 
Now your hopper is a lot like my loader, you may have worked on it but that doesn't mean you got it fixed. What is a 3200, extra coin paid out, what will cause a extra coin pay out, hopper brake !!
PUT BRAIN IN GEAR BEFORE PUTTING MOUTH IN MOTION

Offline Badbaud

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Need Fixing 3200 Error
« Reply #7 on: May 03, 2014, 01:08:46 PM »
The white button is not a reset button.

To reset a S+ open and close the door.

If your displays don't blink off then on when door is closed then your door optics don't work.
Let them that don't want any, have memories of not getting any.

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #8 on: May 07, 2014, 11:51:34 AM »
IT  BLINKS

Offline Badbaud

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Need Fixing 3200 Error
« Reply #9 on: May 07, 2014, 02:46:28 PM »
It could be your SSR (Solid State Relay) is bad.

The red box near the hopper plug.

It uses two triacs in series which are turned on by opto triac drivers.
Let them that don't want any, have memories of not getting any.

Offline Badbaud

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Need Fixing 3200 Error
« Reply #10 on: May 07, 2014, 07:47:16 PM »
IT  BLINKS
I posted this to you a couple of days ago but it got redacted by someone.

If you look at the connector the hopper plugs into you will see 6 rectangular slots and a hole towards the bottom for the guide pin.

The slots on the connector are numbered as follows

from top to bottom

7    8
9    10
   o <-------guide pin hole
11  12

If you leave the hopper out and connect to pins 8 and 9 with a normally closed push button you can simulate a coin out each time you press  the button (press it quickly so there is not another hopper time out).

Not sure if the AC voltage is getting to the hopper motor connect a 120V lamp to pins 11 and 12, if the lamp lights you are getting hopper voltage.

Use a DC voltmeter and measure from pin 10 (+) to pin 9 (ground) and check to make sure you are getting the DC voltage that powers the hopper optics.
Let them that don't want any, have memories of not getting any.

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #11 on: May 11, 2014, 03:13:11 PM »
I do not have or I do not see a red box.  But ID run that jumper with the push button to eight and nine pins.  And that's working following push it bell rings and applies coin.  I also ran 120 volts 11 and 12 pens.  And hopper running good Thank you

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #12 on: May 11, 2014, 03:47:54 PM »
 Also I don't know if this has anything to do it that I'm trying to get the settings correct and menu at five 5.0 and seven I had tried 7.1 80, 7.2, 300, 7.3 9999, then I have a seven only I put 2000 in that box.  8, 0040 then I'd tried 7.1 0000 7.2 1200 7.3 9999, 7.?  2000, 8.?  0000, I'm trying to set it up for that if you win up two 40 quarters.  Anything over goes to credit.  Maximum payout 40 quarters.  All bills goes to credit

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #13 on: May 11, 2014, 05:20:28 PM »
also on the hopper optical I replaced it with a new one but the old one had three wires in the new one has four where does the white go.?

Offline Badbaud

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Need Fixing 3200 Error
« Reply #14 on: May 11, 2014, 05:46:57 PM »
Usually, and don't quote me, the white is the receiver, red is transmitter, green is common with black.
Let them that don't want any, have memories of not getting any.

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #15 on: May 11, 2014, 06:01:41 PM »
 I don't have a black one I have white green red yellow where can I put a white one it sounds like I need it

Offline Badbaud

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3677
  • Reputation Power: 317
  • Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!Badbaud Is an-NLG GOD!
  • (shop) klar.slotrepair@gmail.com
Re: Need Fixing 3200 Error
« Reply #16 on: May 11, 2014, 06:46:15 PM »
Here is a wiring diagram.  Wiring color code is the same as resistor color code for IGT.

1 = black
2 = brown and so on.

so a wire number of 21 would be brown with black stripe.

20 would be a solid brown wire.
Let them that don't want any, have memories of not getting any.

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #17 on: May 11, 2014, 07:59:28 PM »
  I was hoping on a small clue like an arrow :)where goes and it looks like I need a electrician somebody that is qualified and I was comfortable with it as long as it stays on the hopper skid.  the other optical only had three wires and it worked good.  Till the end it only had green yellow red that was all it worked great.

Offline Buzz

  • In Remembrance of our lost NLG Members
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 434
  • Reputation Power: 79
  • Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.Buzz Has a powerful will.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #18 on: May 11, 2014, 09:39:57 PM »
 Like2know  Let me ask you , do you ever think about what you post ?  Now your saying you had a good set of 3 wire hopper optics and change it to a 4 wire optic. Now yo want one of us to tell you where to connect the 4th wire. I just took a look at the 3 S+ machines I have in the house and all three of them have 3 wire hopper optics. Now has it ever crossed your mind that just maybe you have a set of 4 wire hopper optics that was designed for some other machine.
PUT BRAIN IN GEAR BEFORE PUTTING MOUTH IN MOTION

Offline Like2know

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 81
  • Reputation Power: 7
  • Like2know New User has no influence.
  • Gender: Male
  • NLG
Re: Need Fixing 3200 Error
« Reply #19 on: May 12, 2014, 11:32:27 AM »
 I bought it from rudystealdeal the picture looked exactly like the one I had when I got it is the same thing except one extra wire other than that I can't tell the difference
« Last Edit: May 12, 2014, 04:38:47 PM by Like2know »

 

Cell Phone and Pad Mode

imode wap wap2

NLG Archives

Archives @ newlifegames.net Wayback Machine

Contact Us

NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442
If you find this site helpful, please consider becoming a Contributing NLG Member with a monthly subscription to help cover the cost of pizza, coffee, aspirin, hosting, and bandwidth.
Contributing Members: get unlimited personal messages, can save topics and replies as drafts,
can post to the Classified ads, get unlimited access to the downloads, and also get this minty badge:



**Subscription Link** (Click Here) **Subscription Link**



           
If you would rather remain anonymous Thank You or just want to help support the site, please use this "make a donation" button:




From your entire NLG staff, thank you for supporting NLG.


New Life Games LLC 1788 HIGHWAY 95 UNIT 30 BULLHEAD CITY AZ 86442




Newlifegames.com     Newlifegames.net     Newlifegames.org

Newlifegame.com     Newlifegame.net     Newlifegame.org    Newlifegames.us

   New Life Games     NewLifeGames  NLG

 We Bring new Life to old Games    1-888-NLG-SLOTS

Are all Copyright and Trademarks of New Life Games LLC 1992 - 2022


FAIR USE NOTICE:



This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml
If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.




The NewLifeGames.com website is optimized for use with Firefox and a minimum screen resolution of 1600 x 900 pixels.

SimplePortal 2.3.5 © 2008-2012, SimplePortal