Author Topic: Displays netplex is down (Read 4279 times)

qbert · « **Reply #20 on:** November 23, 2021, 12:23:10 PM »

Could a bad fluorescent supply box be drawing the voltage down?

jerzeehamco · « **Reply #21 on:** November 23, 2021, 12:30:29 PM »

So if I was to get a new power supply and it does not fix is the old one still good? There must be more to check why volts are low .?

Tilt · « **Reply #22 on:** November 23, 2021, 12:35:56 PM »

No, those output voltages are too low. If it happened to work with the machine it won't much longer. Usually the DC voltages start to drop as the electrolytic filter caps start failing which increases the AC ripple voltage. If you recap the power supply it should resolve that problem.

jerzeehamco · « **Reply #23 on:** November 23, 2021, 12:47:29 PM »

So not sure what special talent I need to do but if it is possable I am sure I could if I new what recap power supply actually was. So I guess I need a new one (you think) and this power supply is one behind reels or mpu thing that no longer has green bat.?

Tilt · « **Reply #24 on:** November 23, 2021, 12:59:56 PM »

Recap means (re)place all the electrolytic (cap)acitors inside the power supply. You need to know how to solder/desolder electronic components and have to right tools to do it. Electrolytic capacitors, like a battery, have a polarity so you have to be careful that you don't install it backwards. It you do it will likely explode or damage another component.

Yes, the power supply is behind the reels.

qbert · « **Reply #25 on:** November 23, 2021, 01:07:05 PM »

My suggestion just buy a new power supply, it won't kill you to have a spare if it's not the problem. They are still relatively inexpensive. Check with one of the vendors on this site.

jerzeehamco · « **Reply #26 on:** November 23, 2021, 01:23:40 PM »

Ok I have tools and all the ability to do so ( what journeyman carpenter wouldn't).....but this sounds like alot to do without being sure it will so I will get another and see what happens. Thanks Anyb.ody on Here holding a power supply ? Hit me up if ya do please.

qbert · « **Reply #27 on:** November 23, 2021, 01:28:05 PM »

If it is the problem you can recap the old one at your leisure and have a spare.

qbert · « **Reply #28 on:** November 23, 2021, 01:29:48 PM »

Place a WTB in the classifieds on this site.

jerzeehamco · « **Reply #29 on:** November 23, 2021, 01:59:36 PM »

And if it is not I will have a spare that I won't need to cap!

jerzeehamco · « **Reply #30 on:** November 23, 2021, 02:22:14 PM »

Just ordered 1 awaiting delivery keep ya posted when it arrives!

jerzeehamco · « **Reply #31 on:** December 04, 2021, 06:42:27 PM »

ok power supply swapped with new one now says call attendant and light on top machine illuminated!

henrydwh · « **Reply #32 on:** December 04, 2021, 06:57:36 PM »

I am new to this myself, but have you tried turning the jackpot reset key? I had the same error, turned out to be a bad ground. But I had to use the jackpot reset to clear several errors and then found out I had a bad MPU.

Tilt · « **Reply #33 on:** December 04, 2021, 08:05:34 PM »

Quote from: jerzeehamco on December 04, 2021, 06:42:27 PM

ok power supply swapped with new one now says call attendant and light on top machine illuminated!

Open the main door, the horn should go off, and the VFD will tell you what the error is. Probably a RAM error. Turn the jackpot key like henry said. Turn it until it says press and hold the self test button for 2-3 seconds. It's the one on the front of the MPU board. Then it will tell you to close the main door. Do that and wait. It will probably come up and say call attendant again, open the door and it will probably be an EEPROM error. Do the same thing as you did for the RAM error. Hopefully after that round it will spin the reels and come up ready for a coin/bill.

jerzeehamco · « **Reply #34 on:** December 04, 2021, 08:15:05 PM »

now says game eprom crc mismatch 0XB00001

henrydwh · « **Reply #35 on:** December 04, 2021, 08:20:52 PM »

Had the same error, keep turning the reset key till the game starts or you can't clear the error.

jerzeehamco · « **Reply #36 on:** December 04, 2021, 08:22:14 PM »

up and running

qbert · « **Reply #37 on:** December 04, 2021, 08:24:07 PM »

Congrats now you can recap the old power supply at your leisure. 👍

henrydwh · « **Reply #38 on:** December 04, 2021, 08:26:36 PM »

That is great!

Hope I have the same results on Monday when my board gets here!

jerzeehamco · « **Reply #39 on:** December 04, 2021, 08:31:24 PM »

ooppps not so quick it wont take bills now little red dot in 2 corners

News:

NLG Site Navigation Menu

Author Topic: Displays netplex is down (Read 4279 times)