To low Pay out Bally Mustang

[buybestslots]

take pic of wiper side of hopper and post it

[Jon]

I believe you said the wiper board stops at the proper place such as 10 coins but you still only get 7 to 9 coins the first place I would look is at the switch picture included off of your hopper if it is dirty or out of adjustment and looks to be a little out of adjustment it could cause the machine to think it paid 10 and only pay 7 or 9 pretty common

[buybestslots]

I believe you said the wiper board stops at the proper place such as 10 coins but you still only get 7 to 9 coins the first place I would look is at the switch picture included off of your hopper if it is dirty or out of adjustment and looks to be a little out of adjustment it could cause the machine to think it paid 10 and only pay 7 or 9 pret
if switch was dirty it would over pay if  wiper board is not setting  right it  will go off ten pay foil  early , only other thing  could be wiper is not resetting  to zero so if it starts at  1 coin you will get short pay , I'm still betting its wiper board in his pic you could tell it was cocked

[JanGbg]

I believe you said the wiper board stops at the proper place such as 10 coins but you still only get 7 to 9 coins the first place I would look is at the switch picture included off of your hopper if it is dirty or out of adjustment and looks to be a little out of adjustment it could cause the machine to think it paid 10 and only pay 7 or 9 pretty common

I have done that adjustment s lot of times in different Machines. I done it twice here to be sure it ok.

[buybestslots]

twist the wiper board

[JanGbg]

take pic of wiper side of hopper and post it

I'm not sure what you mean with "wiper side". But I'll post pics from different angels.

[JanGbg]

And the rest.

[JanGbg]

twist the wiper board

I done that yesterday as you can see of the new pics from today. :-)

[buybestslots]

when you do step up coil by hand when dose it go off 10 pay? how many clicks it should go off at ten click it 9 times  move board till it just on 10pay foil at  9 clicks, one other thing it could be is kicker is licking a coin off track after its counted back in to hopper

[JanGbg]

when you do step up coil by hand when dose it go off 10 pay? how many clicks it should go off at ten click it 9 times  move board till it just on 10pay foil at  9 clicks, one other thing it could be is kicker is licking a coin off track after its counted back in to hopper

Here is a pic of the board after 10 push on the step-up coil.

[Amechanic]

when you do step up coil by hand when dose it go off 10 pay? how many clicks it should go off at ten click it 9 times  move board till it just on 10pay foil at  9 clicks, one other thing it could be is kicker is licking a coin off track after its counted back in to hopper

   your wiper looks to be stopping at the correct spot, but for some reason the coins are falling back into the hopper rather then out to the payout tray.. Check your hopper knife adjustment..

[buybestslots]

 

when you do step up coil by hand when dose it go off 10 pay? how many clicks it should go off at ten click it 9 times  move board till it just on 10pay foil at  9 clicks, one other thing it could be is kicker is licking a coin off track after its counted back in to hopper

   your wiper looks to be stopping at the correct spot, but for some reason the coins are falling back into the hopper rather then out to the payout tray.. Check your hopper knife adjustment..

[JanGbg]

when you do step up coil by hand when dose it go off 10 pay? how many clicks it should go off at ten click it 9 times  move board till it just on 10pay foil at  9 clicks, one other thing it could be is kicker is licking a coin off track after its counted back in to hopper

   your wiper looks to be stopping at the correct spot, but for some reason the coins are falling back into the hopper rather then out to the payout tray.. Check your hopper knife adjustment..

Where is the "hopper knife" located?

[OldReno]

You might want to add another half turn onto your torsion spring, which is wrapped around your white plastic step up gear.  Often having too little tension will allow the step up fingers to double step, especially on the first coin or two out.  And make sure the spring lies cleanly and does not wrap over itself.  This can happen especially if it is a solenoid step hopper rather than a mechanically stepped one.

[JanGbg]

You might want to add another half turn onto your torsion spring, which is wrapped around your white plastic step up gear.  Often having too little tension will allow the step up fingers to double step, especially on the first coin or two out.  And make sure the spring lies cleanly and does not wrap over itself.  This can happen especially if it is a solenoid step hopper rather than a mechanically stepped one.

I Think it's a combination of faults here! After I fix the "wiper-plate" my machine pays much better! In stead of 16-17 for 20 it now pays 19 or 20. :-). It pays 8-9 for a 10 win and it pays 2 for a 2 win 9 of 10 times.
I'll try Old Renos (The king of this board!) advice after the weekend, tomorow I will go and visit my Young son who is a realy good hockeyplayer! I wish you all a very nice weekend an thanks for your advice!

[JanGbg]

You might want to add another half turn onto your torsion spring, which is wrapped around your white plastic step up gear.  Often having too little tension will allow the step up fingers to double step, especially on the first coin or two out.  And make sure the spring lies cleanly and does not wrap over itself.  This can happen especially if it is a solenoid step hopper rather than a mechanically stepped one.

I Think it's a combination of faults here! After I fix the "wiper-plate" my machine pays much better! In stead of 16-17 for 20 it now pays 19 or 20. :-). It pays 8-9 for a 10 win and it pays 2 for a 2 win 9 of 10 times.
I'll try Old Renos (The king of this board!) advice after the weekend, tomorow I will go and visit my Young son who is a realy good hockeyplayer! I wish you all a very nice weekend an thanks for your advice!

Tonight I'll drink a lot of bears and play a lot on my 5 different Bally Machines! :-)

[buybestslots]

You might want to add another half turn onto your torsion spring, which is wrapped around your white plastic step up gear.  Often having too little tension will allow the step up fingers to double step, especially on the first coin or two out.  And make sure the spring lies cleanly and does not wrap over itself.  This can happen especially if it is a solenoid step hopper rather than a mechanically stepped one.

I Think it's a combination of faults here! After I fix the "wiper-plate" my machine pays much better! In stead of 16-17 for 20 it now pays 19 or 20. :-). It pays 8-9 for a 10 win and it pays 2 for a 2 win 9 of 10 times.
I'll try Old Renos (The king of this board!) advice after the weekend, tomorow I will go and visit my Young son who is a realy good hockeyplayer! I wish you all a very nice weekend an thanks for your a
if moving the board helped your pays try to move it a bit more those foils do wear out  and your game is very old  you might have to make screw holes  out of round with a file or drill bit  not with a  power drill  to move it a hair more counter clockwise